lfs-book/chapter06/iproute2.xml

<?xml version="1.0" encoding="ISO-8859-1"?>
<!DOCTYPE sect1 PUBLIC "-//OASIS//DTD DocBook XML V4.3//EN" "http://www.oasis-open.org/docbook/xml/4.3/docbookx.dtd" [
  <!ENTITY % general-entities SYSTEM "../general.ent">
  %general-entities;
]>
<sect1 id="ch-system-iproute2" xreflabel="IProute2" role="wrap">
  <title>Iproute2-&iproute2-version;</title>
<?dbhtml filename="iproute2.html"?>
  <indexterm zone="ch-system-iproute2">
    <primary sortas="a-iproute2">iproute2</primary>
  </indexterm>
  <sect2 role="package">
    <title/>
    <para>The iproute2 package contains programs for basic and advanced
          IPV4-based networking.
    </para>
    <segmentedlist>
      <segtitle>&buildtime;</segtitle>
      <segtitle>&diskspace;</segtitle>
      <seglistitem>
        <seg>0.1 SBU</seg>
        <seg>.6 MB</seg>
      </seglistitem>
    </segmentedlist>
    <segmentedlist>
      <segtitle>iproute2 installation depends on</segtitle>
      <seglistitem>
        <seg>sed, GCC, Glibc, Make, Linux-Headers</seg>
      </seglistitem>
    </segmentedlist>
  </sect2>
  <sect2 role="installation">
    <title>Installation of iproute2</title>
    <para>The <command>arpd</command> binary included in this package is
          dependent on Berkeley DB.  As <command>arpd</command> is not a very
          common requirement on a base Linux system we remove the dependency on
          Berkeley DB by applying the patch using the command below.  If you
          need the <command>arpd</command> binary, then instructions for
          compiling Berkeley DB can be found in the <ulink
          url="http://www.linuxfromscratch.org/blfs/view/cvs/content/databases.html#db">BLFS book</ulink>.
    </para>

    <screen><userinput>patch -Np1 -i ../iproute2-&iproute2-patch-version;-remove_db-1.patch</userinput></screen>

    <para>Prepare iproute2 for compilation:</para>
    <screen> <userinput>./configure </userinput></screen>

    <para>Compile the package:</para>

    <screen><userinput>make SBINDIR=/sbin</userinput></screen>

    <variablelist>
    <varlistentry>
    <term><parameter>SBINDIR=/sbin</parameter></term>
    <listitem><para>This makes sure that the iproute2 binaries will install into
      <filename class="directory">/sbin</filename>.  This is the correct
      location according to the FHS, as some of the iproute2 binaries are used
      in our bootscripts.</para>
    </listitem>
    </varlistentry>
    </variablelist>

    <para>Now install it:</para>

    <screen><userinput>make install SBINDIR=/sbin</userinput></screen>
  </sect2>

  <sect2 id="contents-iproute2" role="content">
    <title>Contents of iproute2</title>
    <segmentedlist>
      <segtitle>Installed programs</segtitle>
      <seglistitem>
        <seg>ifstat, ip, nstat, routef, routel, rtmon, rtstat, ss, and tc.</seg>
      </seglistitem>
    </segmentedlist>

    <variablelist>
      <title>Short descriptions</title>

      <varlistentry id="ifstat">
        <term>
          <command>ifstat</command>
        </term>
        <listitem>
          <indexterm zone="ch-system-iproute2 ifstat">
            <primary sortas="b-ifstat">ifstat</primary>
          </indexterm>
          <para>shows the interfaces statistics. Shows the amount of transmitted
                and received packages by interface</para>
        </listitem>
      </varlistentry>

      <varlistentry id="ip">
        <term>
          <command>ip</command>
        </term>
        <listitem>
          <indexterm zone="ch-system-iproute2 ip">
            <primary sortas="b-ip">ip</primary>
          </indexterm>

          <para>is the main executable. Has several different functions.</para>

          <para><command>ip link <replaceable>[device]</replaceable></command>
                allows you to look at the state of devices and to change it.
          </para>

          <para><command>ip addr</command> allows you to look at addresses and
                their properties, add new addresses and to delete old ones.
          </para>

          <para><command>ip neighbor</command> allows you to look at neighbour
                bindings and their properties, add new neighbour entries and to
                delete old ones.
          </para>

          <para><command>ip rule</command> allows you to look at the routing
                policies and change them.
          </para>

          <para><command>ip route</command> allows you to look at the routing
                table and change routing table rules.
          </para>

          <para><command>ip tunnel</command> allows you to look at the ip
                tunnels and their properties, and change them.
          </para>

          <para><command>ip maddr</command> allows you to look at the multicast
                addresses and their properties, and change them.
          </para>

          <para><command>ip mroute</command> allows you to set, change, or
                delete the mutlicast routing.
          </para>

          <para><command>ip monitor</command> allows you to monitor the state of
                devices, addresses and routes continuously.
          </para>
        </listitem>
      </varlistentry>

      <varlistentry id="nstat">
        <term>
          <command>nstat</command>
        </term>
        <listitem>
          <indexterm zone="ch-system-iproute2 nstat">
            <primary sortas="b-nstat">nstat</primary>
          </indexterm>
          <para>Shows network statistics</para>
        </listitem>
      </varlistentry>

      <varlistentry id="routef">
        <term>
          <command>routef</command>
        </term>
        <listitem>
          <indexterm zone="ch-system-iproute2 routef">
            <primary sortas="b-routef">routef</primary>
          </indexterm>
          <para>A component of ip route. This is for flushing the routing
                tables.
          </para>
        </listitem>
      </varlistentry>

      <varlistentry id="routel">
        <term>
          <command>routel</command>
        </term>
        <listitem>
          <indexterm zone="ch-system-iproute2 routel">
            <primary sortas="b-routel">routel</primary>
          </indexterm>
          <para>A component of ip route. This is for listing the routing
                tables.
          </para>
        </listitem>
      </varlistentry>

      <varlistentry id="rtmon">
        <term>
          <command>rtmon</command>
        </term>
        <listitem>
          <indexterm zone="ch-system-iproute2 rtmon">
            <primary sortas="b-rtmon">rtmon</primary>
          </indexterm>
          <para>Route Monitoring Utility.</para>
        </listitem>
      </varlistentry>

      <varlistentry id="rtstat">
        <term>
          <command>rtstat</command>
        </term>
        <listitem>
          <indexterm zone="ch-system-iproute2 rtstat">
            <primary sortas="b-rtstat">rtstat</primary>
          </indexterm>
          <para>Route Status Utility</para>
        </listitem>
      </varlistentry>

      <varlistentry id="ss">
        <term>
          <command>ss</command>
        </term>
        <listitem>
          <indexterm zone="ch-system-iproute2 ss">
            <primary sortas="b-ss">ss</primary>
          </indexterm>
          <para>Similar to the netstat command. Shows active connections.</para>
        </listitem>
      </varlistentry>

      <varlistentry id="tc">
        <term>
          <command>tc</command>
        </term>
        <listitem>
          <indexterm zone="ch-system-iproute2 ss">
            <primary sortas="b-tc">tc</primary>
          </indexterm>
          <para>Traffic Controlling Executable. This is for QOS/COS
                implementations.
          </para>

          <para><command>tc qdisc</command> allows you to setup the queueing
                discipline.
          </para>

          <para><command>tc class</command> allows you to setup classes based on
                the queuing discipline scheduling.
          </para>

          <para><command>tc estimator</command> allows you to estimate the
                network flow into a network.
          </para>

          <para><command>tc filter</command> allows you to setup the QOS/COS
                packet filtering.
          </para>

          <para><command>tc policy</command> allows you to setup the QOS/COS
                policies.
          </para>
        </listitem>
      </varlistentry>
    </variablelist>
  </sect2>
</sect1>